- #QPST CONFIGURATION DOES NO PHONE INSTALL#
- #QPST CONFIGURATION DOES NO PHONE SERIAL#
- #QPST CONFIGURATION DOES NO PHONE DRIVERS#
- #QPST CONFIGURATION DOES NO PHONE DRIVER#
- #QPST CONFIGURATION DOES NO PHONE ANDROID#
Its all thanks to nuttmeg for these files.
The QPST setup file and prl file is from samsung admire's thread. AND it was killing my battery from searching for 4G Please check your own ISP support this also.I started looking for a way to change the prl I updated OTA from 3027 back down to 3026 because it was disconnecting my 4G every few minutes. You can confirm 256QAM and 64QAM support with NSG application. That enable 256QAM/64QAM also on second SIM slot. If you have Dual SIM-model, then copy also *_Subscription01 to same location and replace original files. Move lte_category file with EFS Explorer to /nv/item_files/modem/lte/common/lte_category Move disable_cap_ies file with EFS Explorer to /nv/item_files/modem/lte/rrc/cap/disable_cap_ies Connect back to your phone with USB to computer and open EFS Explorer.
#QPST CONFIGURATION DOES NO PHONE ANDROID#
This required also root and does not work anymore on XZ Premium with Android 9.ĭownload disable_cap_ies-30-6-2018 and extract that. EXTRA: Enable 256QAM and 64QAM on Sony XZ and Sony XZ Premium Open app and disable CustomizationSelector. If you could not do that directly on App Info, then you need Disable Appliation -app. I recommend also disable CustomizationSelector application from Android phone on Android Settings -> Apps because this might change settings back when you switch SIM-cards We recommended disable US and Japan bands because we do not needed that in EU-area. You can confirm Band support now with Network Signal Guru application. Save file and then copy file back to your phone.Ĭlose EFS Explorer and QPST-application and reboot your phone. That enables all CA-combos what phone support. On XZ2 please clear ca_band_combos line on eu_fin_mccs (depends your MCC) like on screenshot. Open this file example on Notepad++ application and move Finnish MCC 244 from eu_little_mccs to eu_big_mccs section. If you have Dual SIM-version, you should see also carrier_policy_Subscription01.xml file. Then go to policyman directory and on directory copy carrier_policy.xml to your desktop. Now open on Start Clients menu -> QPST EFS Explorer. Keep this file safe if you need anytime recover original settings. Go to Backup tab and select location with Browse button where you like save backup file. Open Start Client -menu and then select Software Download. Let’s make now modem backup before we edit it. It use same interface as QPST so cannot run same time. If you do not see phone on list, please make sure you do not have Network Signal Guru App same time open on your phone. Now you should see modem on active phone list.
#QPST CONFIGURATION DOES NO PHONE SERIAL#
Uncheck “Show Serial and USB/QC Diagnostic ports only” to see COM3 port. If you do not see on this list, you must add it to manually via Ports. You should see now on active phone list your device.
#QPST CONFIGURATION DOES NO PHONE DRIVER#
Now driver has installed and you can see that on modem section. Then select Qualcomm Android Modem 9018 -driver and Next. Select “Have Disk…” Find then from extracted ZIP-file qcmdm.inf driver-file.
#QPST CONFIGURATION DOES NO PHONE DRIVERS#
Select “Let me pick from a list of available drivers on my computer” Select “Browse my computer for driver software” Download supported drivers here Mi5_Qualcomm_Drivers.
#QPST CONFIGURATION DOES NO PHONE INSTALL#
Install drivers with Update Driver-function. Open on your Windows-desktop Device Manager and you see now 4x F8311 (Sony XZ) undefined device.įind on Device Manager hardware id “MI_04”įind _04 driver. Wait 10 second and enable USB Debugging again and plug USB-cable back to your phone. Then disable USB Debugging on your Android-phone and remove USB-cable from your phone. You can turn off mobem mode after with command F8331:/ $ setprop 0 Open command line and run adb shell -command. Then connect your phone with USB-cable to your desktop. Please enable under Developer Tools USB-Debugging on your Android-phone.